What is coaxial cable and what are its uses

Coaxial Cable

If you require any further information on co-axial cable types that are available to us please fill in the following form and we will get back to you as soon as possible


Please note that all fields followed by an asterisk must be filled in.
First Name* First Name*
Last Name* Last Name*
E-mail Address* E-mail Address*
Country* Country*
Business Phone* Business Phone*
Fax* Fax*
Company name* Company name*
List materials required* List materials required*
Delivery requirements i.e. Ex works, F.O.B. or delivered to site U.K. etc.

The following is for your information:-

Coaxial cable is an electrical cable consisting of a round conducting wire, surrounded by an insulating spacer, surrounded by a cylindrical conducting sheath, usually surrounded by a final insulating layer. It is used as a high-frequency transmission line to carry a high-frequency or broadband signal. Because the electromagnetic field carrying the signal exists (ideally) only in the space between the inner and outer conductors, it cannot interfere with or suffer interference from external electromagnetic fields.

Description

Coaxial cables may be rigid or flexible. Rigid types have a solid sheath, while flexible types have a braided sheath, usually of thin copper wire. The inner insulator, also called the dielectric, has a significant effect on the cable's properties, such as its characteristic impedance and its attenuation. The dielectric may be solid or perforated with air spaces. Connections to the ends of coaxial cables are usually made with RF connectors.

Signal propagation

Open wire transmission lines have the property that the electromagnetic wave propagating down the line extends into the space surrounding the parallel wires. These lines have low loss, but also have undesirable characteristics. They cannot be bent, twisted or otherwise shaped without changing their characteristic impedance. They also cannot be run along or attached to anything conductive, as the extended fields will induce currents in the nearby conductors causing unwanted radiation and detuning of the line.

Coaxial lines solve this problem by confining the electromagnetic wave to the area inside the cable, between the center conductor and the shield. The transmission of energy in the line occurs totally through the dielectric inside the cable between the conductors. Coaxial lines can therefore be bent and twisted (subject to limits) without negative effects, and they can be strapped to conductive supports without inducing unwanted currents in them. The inner conductor can be made of braid and the outer conductor can be made of corrugated tube for greater flexibility, but this comes at the cost of increased ohmic losses and lower phase velocity. The outer conductor can also be made of (in order of increasing leakage) wound foil, woven tape, or braid.

In radio-frequency applications up to a few gigahertz, the wave propagates only in the transverse electric magnetic (TEM) mode, which means that the electric and magnetic fields are both perpendicular to the direction of propagation. However, above a certain cutoff frequency, transverse electric (TE) and/or transverse magnetic (TM) modes can also propagate, as they do in a waveguide. It is usually undesirable to transmit signals above the cutoff frequency, since it may cause multiple modes with different phase velocities to propagate, interfering with each other. The outer diameter is roughly inversely proportional to the cutoff frequency.

Coaxial cables require an internal structure of an insulating (dielectric) material to maintain the spacing between the center conductor and shield. Unfortunately, all dielectrics have loss associated with them, which causes most coaxial lines to have more loss than open wire lines. In typical applications the loss in polyethylene is comparable to the ohmic loss at 1 GHz and the loss in PTFE is comparable to ohmic losses at 10 GHz. Most cables have a solid dielectric; others have a foam dielectric which contains as much air as possible to reduce the losses. Foam coax will have about 15% less attenuation but can absorb moisture � especially at its many surfaces � in humid environments, increasing the loss. Stars or spokes are even better, but more expensive. Still more expensive were the air spaced coaxials used for some inter-city communications in the middle Twentieth Century. The center conductor was suspended by polyethylene discs, every few centimeters. In any case the lower dielectric constant of air allows for a greater inner diameter at the same impedance and a greater outer diameter at the same cutoff frequency, lowering ohmic losses.

Standards

Most coaxial cables have a characteristic impedance of either 50, 52, 75, or 93 Ω. The RF industry uses standard type-names for coaxial cables. Thanks to television, RG-6 is the majority of coaxial cable, and the majority of connections are by F connectors.

A series of standard types of coaxial cable were specified for military uses, in the form "RG-#" or "RG-#/U" (RG from Radio Guide or Radio Grade, /U indicates multiple uses). They go back to World War II and were listed in MIL-HDBK-216 published in 1962. These designations are now obsolete. The current military standard is MIL-SPEC MIL-C-17. MIL-C-17 numbers, such as "M17/75-RG214," are given for military cables and manufacturer's catalog numbers for civilian applications. However, the RG-series designations were so common for generations that they are still used, although critical users should be aware that since the handbook is withdrawn there is no standard to guarantee the electrical and physical characteristics of a cable described as "RG-# type". The RG designators are mostly used to identify compatible connectors that fit the inner conductor, dielectric, and jacket dimensions of the old RG-series cables.

Connectors

From the signal point of view, a connector can be viewed as a short, rigid cable. The connector usually has the same impedance as the related cable and probably has a similar cutoff frequency although its dielectric may be different. High-quality connectors are usually gold or rhodium plated, with lower-quality connectors using nickel or tin plating. Silver is occasionally used in some high-end connectors due to its excellent conductivity, but it usually requires extra plating of another metal since silver readily oxidizes in the presence of air.

One increasing development has been the wider adoption of micro-miniature coaxial cable in the consumer electronics sector in recent years. Wire and cable companies such as Tyco, Sumitomo Electric, Hitachi Cable, Fujikura and LS Cable all manufacture these cables, which can be used in cellular phones.

Important parameters

The characteristic impedance in ohms (Ω) is calculated from the ratio of the inner and outer diameters and the dielectric constant. Assuming the dielectric properties of the material inside the cable do not vary appreciably over the operating range of the cable, this impedance is frequency independent. Capacitance, in farads per metre. Resistance, in ohms per metre. Attenuation or loss, in decibels per metre. This is dependent on the loss in the dielectric material filling the cable, and resistive losses in the center conductor and shield. These losses are frequency dependent, the losses becoming higher as the frequency increases. In designing a system, engineers must consider not only the loss in the actual cable itself, but also the insertion loss in the connectors. Outside diameter, which dictates which connectors must be used to terminate the cable. Velocity of propagation, which depends on the type of dielectric. Cutoff frequency

Significance of Impedance

A question that is often asked is what the significance of a 52 or 75 Ω characteristic impedance is. The best coaxial cable impedances to use in high-power, high-voltage, and low-attenuation applications were experimentally determined in 1929 at Bell Laboratories to be 30, 60, and 77 Ω respectively. 30 Ω cable is exceedingly hard to make however, so a compromise between 30 Ω and 60 Ω was reached at 52 Ω, which has persisted. 73 Ω is an exact match for a centre fed dipole aerial/antenna so 75 was adopted as a compromise between 73 and 77 ohms

Uses

Short coaxial cables are commonly used to connect home video equipment, in ham radio setups, and in measurement electronics. They used to be common for implementing computer networks, in particular Ethernet, but twisted pair cables have replaced them in most applications except in the growing consumer Cable modem market for broadband Internet access.

Long distance coaxial cable is used to connect radio networks and television networks, though this has largely been superseded by other more high-tech methods (fibre optics, T1/E1, satellite). It still carries cable television signals to the majority of television receivers, and this purpose consumes the majority of coaxial cable production.

Micro coaxial cables are used in a range of consumers devices, military equipment, and also in ultra-sound scanning equipment.

The most common impedances that are widely used are 50 or 52 ohms, and 75 ohms, although other impedances are available for specific applications. The 50 / 52 ohm cables are widely used for industrial and commercial radio frequency applications (including radio, and telecommunications), although 75 ohms is commonly used for domestic television and radio.

Types

In broadcasting and other forms of radio communication, hard line is a very heavy-duty coaxial cable, where the outside shielding is a rigid or semi-rigid pipe, rather than flexible and braided wire. Hard line is very thick, typically at least a half inch or 13 mm and up to several times that, and has low loss even at high power. It is almost always used in the connection between a transmitter on the ground and the antenna or aerial on the tower. Hard lines are often made to be pressurised with nitrogen or desiccated air, which provide an excellent dielectric even at the high temperatures generated by thousands of watts of RF power, especially during intense summer heat and sunshine. Physical separation between the inner conductor and outer shielding is maintained by spacers, usually made out of tough solid plastics like nylon.

RG/6 is available in three different types designed for various applications. "Plain" or "house" wire is designed for indoor or external house wiring. "Flooded" cable is infused with heavy waterproofing for use in underground conduit. "Messenger" contains some waterproofing but is distinguished by the addition of a steel messenger wire along its length to carry the tension involved in an aerial drop from a utility pole.

Triaxial cable or triax is coaxial cable with a third layer of shielding, insulation and sheathing. The outer shield, which is earthed (grounded), protects the inner shield from electromagnetic interference from outside sources.

Twin-axial cable or twinax is a balanced, twisted pair within a cylindrical shield. It allows a nearly perfect differential signal which is both shielded and balanced to pass through. Multi-conductor coaxial cable is also sometimes used.

Biaxial cable or biax is a figure-8 configuration of two 50 Ω coaxial cables, used in some proprietary computer networks.

Semi-rigid cable is a coaxial form using a solid copper outer sheath. This type of coax offers superior screening compared to cables with a braided outer conductor, especially at higher frequencies. The major disadvantage is that the cable, as its name implies, is not very flexible, and is not intended to be flexed after initial forming.

Interference and Troubleshooting

Coaxial cable insulation can degrade requiring cable replacement, especially if it has been exposed to the elements on a continuous basis. The shield is normally grounded, and if even a single thread of the braid or filament of foil touches the center conductor, the signal will be shorted causing significant or total signal loss. This most often occurs at improperly installed end connectors and splices. Also, the connector or splice must be properly attached to the shield, as this provides the return electrical path for the signal.

Despite being shielded, interference can occur on coaxial cable lines. Susceptibility to interference has little relationship to broad cable type designations (e.g. RG-59, RG-6) but is strongly related to the composition and configuration of the cable's shielding. For cable television, with frequencies extending well into the UHF range, a foil shield is normally provided, and will provide total coverage as well as high effectiveness against high-frequency interference. Foil shielding is ordinarily accompanied by a tinned copper or aluminum braid shield, with anywhere from 60 to 95% coverage. The braid is important to shield effectiveness because (1) it is more effective than foil at absorbing low-frequency interference, (2) it provides higher conductivity to ground than foil, and (3) it makes connectorization easier and more reliable. "Quad-shield" cable, using two low-coverage aluminum braid shields and two layers of foil, is often used in situations involving troublesome interference, but is less effective than a single layer of foil and single high-coverage copper braid shield such as is found on broadcast-quality precision video cable.

In the United States and some other countries, cable channels 2-13 share the same frequency as those from television broadcast towers. If the cable consumer is too close to a television tower and the cable company provides the same station on the like channel, interference and 'ghosting' may result. One solution is to make sure the cable signal is at the maximum allowed strength (especially if splitters are used for multiple TV sets), as this will increase the signal-to-noise ratio (the "noise" being the pickup of the broadcast tower). Choosing coaxial cable with high shield effectiveness, and ensuring that connections are sound and tight, can also help reduce interference. Only industrial-quality cable TV amplifiers (generally not available at retail) should be used to amplify weak signals. Cheaper ones, sold at consumer electronics stores, often cause more problems than they solve.

This information has been reprinted from Wikipedia and can be reproduced subject to their copyright conditions which can be reviewed at the following link.

Wikipedia copyright conditions

All done at our coaxial cable page? click to go back to cables.